Seamless Rain Gutters

Seamless rain gutters install straighter than conventional standard length sectional rain gutters and look more attractive. Seamless rain gutters are made right on the job site using portable seamless rain gutter forming machines. They can be made to almost any length needed and are only limited by the length of the coil stock rolls of aluminum available. Seamless rain gutters are less likely to leak than conventional rain gutters because there are far less joints to seal. They are available in different color options to match or contrast the color of your siding.

Leaf guards are a low maintenance option and are also available for installation with your seamless rain gutters.

How Leafproof® works

Except in areas where the roof line has concentrated water flow (such as an inside valley), water flowing off the roof does not shoot to the front of the gutter. It simply follows the roof line, on to the drip edge which is under the shingles, and down the back of the gutter. The reason that the water does not shoot to the front lip is that water clings to the surface it is flowing over. This is known as surface tension. Surface tension can best be visualized by slightly tipping a glass of water and watching the water run down the side of the glass.

Patented “S-Bend" Technology

LeafProof® makes surface tension work for you, the homeowner. The “S” bend causes the water flow to reverse and churn, which slows the momentum of the water as it comes off the roof. The “S” bend also permits the portion of the Leafproof panel which covers the gutter, to be installed at a fairly level slope. This reduces the speed of the water even more. As a result, when the water flow reaches Leafproof’s® water channel, the water flow once again reverses and drains into the gutter.

There are other gutter covers on the market that work in a similar manner. However, these gutter covers do not have Leafproof’s® patented “S” bend. This means these covers must be installed under the second row of shingles and are often screwed or nailed into the roof.


THEIRS vs LEAFPROOF® Comparisons

Screens

Vinyl

Domed

Combinations

Leafproof® is a solid aluminum gutter cover that installs over existing gutters without penetrating your roof. The patented “S-Bend” slows the flow of rainwater, causing the water to adhere to the Leafproof® panel.

The Leafproof® System can be installed on any type of roofing, including shingles, slate, metal and tile, and on any roof pitch.

The patent-pending ChannelGuard™ option offers additional protection against even the smallest debris. The ChannelGuard™ uses a “debris fence” to keep small leaves, pine needles, seeds and virtually all other debris out of the water channel. Leafproof® with ChannelGuard™ is the first and only gutter protection product designed to be virtually maintenance free.

Leafproof®- XP is ideal where extreme protection is needed. XP was designed to handle rainwater in high flow areas like metal roofs, steep roofs, and roof valleys. The diamond vents allow rainwater to flow into the gutters while keeping leaves and debris out.

How does LeafProof® work?

Patented “S” Bend Technology

LeafProof® is a solid aluminum gutter cover that works on the principle of surface tension. Surface tension can best be visualized by slightly tipping a glass of water and watching the water run down the side of the glass.
Leafproof makes surface tension work for you, the homeowner. The patented “S” bend causes the water flow to reverse and churn, which slows the momentum of the water as it comes off the roof. The “S” bend also permits the portion of the Leafproof panel which covers the gutter, to be installed at a fairly level slope. This reduces the speed of the water even more. As a result, when the water flow reaches Leafproof’s water channel, the water flow once again reverses and drains into the gutter.

How does LeafProof® prevent leaves and other debris from entering the gutter?

If you view LeafProof® from directly above you cannot see LeafProof’s® water channel. When the flow of water reaches the point directly above the water channel, the flow will reverse direction as a result of surface tension, and the water will drain into the gutter. Most debris will not follow this reversal or is blown off the roof by the wind when dry.

Will a very heavy rain overflow LeafProof®?

No. When properly installed, LeafProof® will handle the heaviest rainfall ever recorded in one hour in America (11 inches). Rainfall this heavy is an extremely rare and dangerous occurrence. (If it is raining this hard, you will not be concerned about your gutters, you will be wondering if there is any room on the "ark"!) In fact, most gutter systems will overflow between 3 to 4 inches per hour. Therefore, manufacturers that advertise their gutter cover can handle 21 inches of rain an hour are misleading because most gutters cannot handle this amount of rainfall.

Will LeafProof® work on roofs with steep pitches?

Yes, LeafProof’s® patented "S" bend and design will reduce the water’s speed and permit the water to enter the water channel without overflow.

Is it important that a gutter cover have a pre-set water channel?

Yes, some gutter covers drain the water through a gap between the cover and front lip of the gutter. In many instances, the front lip of the gutter has been slightly bent or damaged through normal wear, which causes the width and size of the gap to vary in size. This opening creates the potential for birds or debris to enter the gutter.

Can squirrels or birds enter and build nests?

No. LeafProof® is made from aluminum, not vinyl. Therefore squirrels and birds cannot chew or peck through a section of LeafProof®. Additionally, unlike some "all-in-one gutter and gutter covers", birds cannot enter through the water channel because the opening is too small.

How can LeafProof® be cleaned from the ground?

On RARE occasions, LeafProof’s® water channel may trap some debris. This debris will be visible from the ground and may be removed using a hose with a high-pressure nozzle to clear the water channel of the visible debris. Choosing Leafproof® with ChannelGuard will virtually eliminate debris from getting trapped in the water channel.

Why is it important that a homeowner be able to clean a gutter cover from the ground?

Any product that is placed on the exterior of a home will require some maintenance. For example, windows and vinyl siding must be cleaned. Gutter covers are not an exception. Gutter cover manufacturers that claim their product is maintenance-free and will never clog are simply not stating the truth. LeafProof® is the only gutter cover on the market that is installed under the first row of shingles and allows you to perform this necessary maintenance without climbing on a ladder or standing on your roof. The brand new ChannelGuard option will significantly reduce the likelihood of even the smallest debris from entering the pre-set water channel making Leafproof with ChannelGuard the closest “Maintenance free” gutter cover on the market today!

How does the new ChannelGuard option work?

This exciting, optional piece is the most significant advancement in gutter protection since the introduction of the “S” bend.The patent-pending ChannelGuard option offers additional protection against even the smallest debris. The ChannelGuard uses a “debris fence” to keep small leaves, pine needles, seeds and virtually all other debris out of the water channel. Leafproof with ChannelGuard is the first and only gutter protection product designed to be virtually maintenance free.

Is LeafProof® nailed or screwed into the roof or fascia?

No. LeafProof® simply slides under the first row of shingles and the front is securely attached to the gutter lip. Products that are nailed or screwed into the roof may cause serious damage to your roof and may void many roofing warranties.

Why is it important that the gutter cover fits under the first row of shingles?

The difference in the height of a gutter cover that fits under the second row instead of the first row of shingles on a 5/12-pitch roof is approximately 11⁄2 inches. This difference in height means that the gutter cover is much more visible which detracts from the appearance of the home. LeafProof® fits securely under the first row of your existing shingles and will provide a more finished look to your home’s exterior.

Why is LeafProof® installation more expensive than a traditional gutter installation?

LeafProof® is custom-installed to fit your roof pitch while most gutters can be formed and measured to length at the job site. Since LeafProof® must be installed under the shingle, a long run of LeafProof® would be very difficult, if not impossible, to install. Therefore, LeafProof® is manufactured and installed using four-foot sections. If gutters were installed four feet at a time, their cost would significantly increase, too.

Are more expensive products better than LeafProof®?

No. LeafProof® is the only product on the market that: fits existing gutters; is installed under the first row of shingles; is not screwed into your roof or fascia; and can be cleaned from the ground. Competing products are more expensive because increased installation time greatly adds to the cost OR your existing gutters must be replaced. Although some gutter covers can handle more rain than LeafProof®, this advantage is purely academic; your gutter will overflow before it will rain harder than the amount of water flow LeafProof® can easily handle.

Why is LeafProof® superior to other gutter protection products?

LeafProof® is the only gutter protection product on the market today that: fits existing gutters; can be maintained from the ground; is not screwed into the roof or fascia; and is securely installed under the first row of shingles. There are other gutter covers on the market that work in a similar manner. However, these gutter covers do not have Leafproof’s patented “S” bend. This means these covers must be installed under the second row of shingles and are often screwed or nailed into the roof.

Sundance rain gutters will install a wide variety of specialty and custom gutter systems of nearly any size and type. Our specialty gutters include copper and galvanized with a large variety of accessories to match. Pick your own style and set your house apart from the rest with a touch of personality.

Accessories include:

• Leaderheads
• Custom Downspouts
• Gutter Accessories
• Rain Chains
• Snow Guards
• Leafproof
• Leaf Screens

The Heated Leafproof® System is available for homes in northern climates. The system keeps leaves and debris out of your gutters AND completely eliminates icicle and ice dam formation.

Uneven saturation of the soil around your home’s foundation can cause the soil to heave as it expands and contracts. Heaving is a leading cause of foundation failure.

10 Ways Seamless Rain Gutters Protect the Home

1. MOISTURE CONTROL – Keep basements, crawl spaces, and garages dry and free of conditions that support mold and wood fungi growth by controlling roof drainage.
2. FOUNDATION PROTECTION – Limit the movement of active zone soils underneath the foundation by reducing the amount of water that enters at the foundation wall.
3. PROTECT BACK-FILL – Top soil around the foundation is the weakest link in foundation moisture control. Preventing topsoil erosion can help prevent future structural damage.
4. SHIELD WINDOWS AND DOORS – Most durability issues arise from bulk water intrusion through windows and doors. Roof drainage will direct water away from sensitive areas.
5. PROTECT PLANTS AND SHRUBS – Standing water in flower beds around the home can permit harmful plant fungi to develop as well as attract ants, roaches, and termites.
6. PROTECT FASCIA – Water migration may cause rotting and insects that can be costly to repair. Quickly moving water away from rafter and roof joints is essential to a home’s long term durability.
7. INCREASE ROOF OVERHANG – Rain gutters can add up to 6” of protective roof overhang, providing additional shielding of windows and doors, improving drying times and moisture levels.
8. PREVENT SPLASH BACK – Rain gutters keep siding and masonry looking new by preventing splash back of dirt, grass, and minerals that stain the exterior and can be difficult to remove over time.
9. DECORATIVE DETAIL – Rain gutters are not just functional but can accentuate the architecture of any home. Senox products are available in various styles, colors, and metals.
10. RAINWATER COLLECTION – Collecting rainwater is the simplest way to water your lawn, plants, and foundation all the while contributing to water conservation goals.

Like any other part of your home, your gutters need to be maintained to function properly. Leaves and debris can build up in your gutters clogging the downspout and restricting the flow of water. When the water cannot drain properly, it backs up into the trough causing the gutters overflow. Overflow can lead to water seeping behind the gutter and rotting the fascia. The standing water that remains also creates a perfect breeding ground for mosquitoes. Gutter guards can be added to your gutter system to keep large leaves and debris out in order to prevent clogging and reduce maintenance. Without gutter guards, it is recommended that your gutters be cleaned out 1-3 times a year depending on the number of trees surrounding your home. With gutter guards, it is still recommended to clean out your gutters once a year which could be as simple as using a power washer to spray loose small debris and wash down the downspout.

There are a number of gutter guards to choose from. Some are screens and some are solid covers that use perforations and/or surface tension to pull rain water in while keeping out large leaves and debris.

Customers sometimes call rain gutter companies about dirty streaks on their rain gutter systems that will not wash off easily. The first assumption is usually that the paint has gone bad and turned a different color. That is not always the case. Naturally, pollution and dirt continuously build up on the top lip of the gutter. These pollutants include but are not limited to dirt, dust, emissions from diesel trucks, and smoke from brush fires that are carried in by the wind. When moisture combines with these pollutants, it streams down the face of the gutter. Future precipitation will continuously follow this same path. Over time, the buildup becomes alternating light and dark streaks. This is generally referred to as “tiger striping” and is a problem experienced by manufacturers of trailers, motor homes, commercial architectural aluminum, metal roofing, siding and gutters. Senox has reviewed government and industry guidelines that all require regular maintenance to prevent the “normal buildup of soil deposits and oxide accumulations.” The level of maintenance depends solely on the atmospheric conditions in a geographic region.

Beauty -
Gutters should add to your home, not distract from it. That is why we offer the largest selection of colors in the industry: 26 painted aluminum colors as well as copper and galvalume.

Quality -
Senox products are made with the highest standards in quality control. Raw materials: coil thickness meets specifications, the paint is even and the color is correct: angles are correct, seams on downpsouts and elbows are secure, parts are without cracks

Reliability -
Senox carries the largest selection of gutter products, colors and produce accessories such as elbows, offsets, endcaps and miters from the same pre-coated coil that is used to form the gutters so that the color remains consistant.